Dhaka Mobile 

Logo 




Go Back  

Dhaka Mobile > Product Support Sections > No More Supported/Dead Box > MX-KEY-(by Alim Hape)

Connect with Facebook
Register Unlock support Online Shop Members List Calendar Mark Forums Read

Reply
 
Thread Tools Display Modes
Old 27-04-09, 07:39 AM   #1
wawan_berau
Banned
 
Join Date: Dec 2008
Location: Indonesia
Posts: 100
Status: Offline
Sonork:
Thanks: 1
Thanked 148 Times in 54 Posts
Rep Power: 0
wawan_berau is on a distinguished road
[Tips] mobileEx in practice

Here i will explain in step to save your time and optimize the job when using mobileEx, specially with 'Nokia Tool'.

- Always select correct 'Generation' first before any operation.
- Always Use "Scan" if you're working with non dead phone, this will help mobileEx to use 'correct' spesific setting for any phones attached to box.
- Make sure phone is in correct mode for any FBUS/NON flashing operation,
example: in Tuning & Testing page phone should be in TEST MODE, else will be best if the phone is in LOCAL MODE.Do phone mode change manually if needed.
- For any operation, specially newly released phones, its better to save its security data (RPL + full pm) first before you do anything else.
- if you noticed, there was a differences of flashing speed between FlashID/Manufacturer
the option 'Fast flash' should not be enabled for flash chip "INTEL"
- if you need only to change the language, select file setting as NORMAL. then check 'Language Only" should do the job
- "Safe Flash" will save RPL backup from flash mode(even a DEAD one except ASIC11 phones).
- Use "Restart" button every time you need to refresh the connection or restart the phone.
- Use "..."(Read Phone Mode) button at the right of the phone mode combo to check if the phone if connected and synchronized.
- mobileEx loads your selected "Products" folder to the phone model list, so make sure you have set the correct folder ("Options").

- to be continued.
  Reply With Quote
The Following 2 Users Say Thank You to wawan_berau For This Useful Post:
Old 25-05-09, 11:36 PM   #2
DeNovo
Administrator
 
DeNovo's Avatar
 
Join Date: Oct 2008
Age: 41
Posts: 399
Status: Offline
Sonork:
Thanks: 198
Thanked 1,742 Times in 260 Posts
Rep Power: 10
DeNovo is on a distinguished road
Default TIPS] MXKEY in practice - What you should know about mobileEx -

  • 1. Always select correct 'Generation' first before any operation.
  • 2. Always Use "Scan" if you're working with non dead phone, this will help mobileEx to use 'correct' spesific setting for any phones attached to box.
  • 3. "BUS Check" with setting safe flash ticked, will perform boot squence, display boot information (upp id, flash manufacture, flash address) and automatically safe phone's rpl.
  • 4. Make sure phone is in correct mode for any FBUS/NON flashing operation,
    - example: in Tuning & Testing page, phone should be in TEST MODE, else will be best if the phone is in LOCAL MODE.
    Do phone mode change manually if needed.
  • 5. When doing jobs on working phone, for any operation (add language, locks, etc), DCT4 and BB5, it is better to save its security data (RPL, certificate, pm, etc) first before you do anything else. Just in case...
  • 6. If you noticed, there was a differences of flashing speed between FlashID/Manufacturer the option 'Fast flash' should not be enabled for "INTEL" flash chip.
  • 7. If you need only to change the language, select file setting as NORMAL. then check 'Language Only"
  • 8. "Safe Flash" will save RPL backup from flash mode, and currently NOT supported for ASIC type 11 phone, so dont be checked. For this phone please do a PM backup since RPL backup from flash mode not yet supported. All other DCT4 asic is supported. Yes, even the dead one. :029:
  • 9. Use "Restart" button every time you need to refresh the connection or restart the phone.
  • 10. Unlock "Security Code" on all DCT4,DCT4PLUS(Asic 2),WD2, TIKU without loosing any user data(phonebook, msg, etc) even counter already blocked? Yes, it is possible using mobileEx. Just do a "BUS Check" and you will see "Master Code" , use this code as the security code(this code readed from the phone and 100% will work both for CDMA or GSM phones).
-----------------------
Customizing Your Suite
-----------------------
Configure Nokia Tool

Open Nokia Service Tool, and click on this corner



>



* Enabled Imei changes -> if checked Imei/Esn changes will visible.
Kindly check for your local law for this operation.

* Auto backup ... -> Backup RPL on BUS check ( for DCT4)

* Auto Create DP folder if not exist
This is for directory creation specialy for .nfp extraction. Inside those directory, mcu, ppm, and cnt will be placed.

* Default FBUS timeout
This will set FBUS timeout (higher value = low speed but more accurate)

* Highlight market item
This will highlight the character you choosed. For example on picture, it highlighted on Indo, APAC, MD, and -X.
You will see like this when you selecting files from product code



Server : this is for your ask>rpl service. choose which one is fastest from your location.



And this is the setting for your firmware directory




thats for now, will add more info :dft003:

Best Regards

Last edited by DeNovo; 25-05-09 at 11:39 PM.
  Reply With Quote
The Following 6 Users Say Thank You to DeNovo For This Useful Post:
Old 13-09-10, 12:12 PM   #3
sahilnayeem
Going Up Member
 
Join Date: Sep 2010
Age: 37
Posts: 47
Status: Offline
Sonork:
Thanks: 165
Thanked 24 Times in 17 Posts
Rep Power: 0
sahilnayeem is on a distinguished road
Default Re: [Tips] mobileEx in practice

Thanks brother for sharing this usefull tips
  Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +7. The time now is 01:26 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Copyright DhakaMobile.com 2006-2016. All Rights Reserved.